Showing results for "6 ft. designer manually retractable awning 36.5 in. projection in cocoa awnings in a box 3020773"

This 6 ft. W x 3 ft. Retractable Window Awning is easy to install

• Cover Material: Woven Acrylic
• Frame Material: Aluminum
• Compatible Installation Surface: Brick; Concrete; Wood
• Level of Assembly: Full Assembly Needed
• Minimum Required Clearance: 2''

Absolutely beautiful !. Patrick. US. 2023-02-20 17:57:37

This is an awning operator of aluminum diecast construction with a gray baked enamel finish used on Air Control-Keller Windows. It is right-handed with a matching crank handle with a 2-3/8 in. link arm. It has an L-shaped mounting hole pattern that is 5-1/4 inches from the center of the top hole to the center of the bottom hole and the two horizontal holes in the bottom leg are 1-1/8 in. on the center.

• Comes in a neutral gray color to blend with existing hardware, in a corrosion-resistant, baked-on enamel finish
• Designed for use with awning windows manufactured by Nu-Aire Windows
• Features an L-shaped mounting hole pattern to provide greater stability when cranking
• For further dimensional and specification information, please see the line drawing
• A Phillips head screwdriver is required for installation

These awning operators are constructed of high pressure diecast zinc and the case and crank come in a beautiful finish. Each operator features a simple detach clip which allows the operator to disengage from the sash's center hook for quick and easy window release. This awning operator mounts on the bottom window sill of crank out awning windows, and holds the sash open at the user's desired location. These operators replace others whose roto gears may have become worn and stripped, or the spline to which the hand cranks attach. Included with each is the operator, a crank, a sash hook and installation fasteners.

• This is a Truth hardware replacement awning operator with a worm drive and Gears have a corrosive resistant E-Gard coating
• Non-handed design
• Crank handle is included
• Diecast meal with beautiful finish
• Please refer to the line art drawing for dimensions and compare with your original item before purchasing

This is an awning operator of aluminum diecast construction with an aluminum painted finish used on Stanley windows. It is left-handed with a matching crank handle with an offset link arm. It has a reversed L-shaped mounting hole pattern with one hole offset on the straight edge. The mounting holes are measured from the center of holes to the center of holes.

• Designed for use with awning windows manufactured by Stanley windows
• Features a reversed L-shaped mounting hole pattern to provide greater stability when cranking
• Awning window operator for Stanley windows
• Diecast housing and crank with case hardened steel gears
• Aluminum-colored enamel finish

This is an awning operator of aluminum diecast construction with a gray baked enamel finish used on Pan-American Windows. It is left-handed with a matching crank handle with a 2-5/8 in. link arm. It has an L-shaped mounting hole pattern that has two top holes that are 5-1/4 in. from the center of the top holes to the center of the bottom hole and the two horizontal holes in the bottom leg are 1-5/16 in. on the center.

• Constructed of diecast and steel material
• Comes in a neutral gray color to blend with existing hardware, in a corrosion-resistant, baked-on enamel finish
• Designed for use with awning windows manufactured by Pan American and Stanley Windows
• Features an L-shaped mounting hole pattern to provide greater stability when cranking
• Please refer to the line art drawing for dimensions and compare with your needs before ordering (Not universal)

This is an awning operator of aluminum diecast construction with a gray baked enamel finish used on Andersen windows. It is left-handed with a matching crank handle with a 2-5/8 in. offset link arm. It has an L-shaped mounting hole pattern with one hole offset on the straight edge. The mounting holes are 4-1/2 in. from the center of the top hole to the center of the bottom hole and the two horizontal holes in the bottom leg are 1-7/16 in. on the center.

• Designed for use with awning windows manufactured by Andersen windows
• Features an L-shaped mounting hole pattern to provide greater stability when cranking
• Awning window operator for Andersen windows
• Diecast housing and crank with case hardened steel gears
• For further dimensional information, please see the line drawing

This is an awning operator of aluminum diecast construction with a gray baked enamel finish used on Pan-American Windows. It is right-handed with a matching crank handle with a 2-5/8 in. link arm. It has an L-shaped mounting hole pattern that has two top holes that are 5-1/4 in. from the center of the top holes to the center of the bottom hole and the two horizontal holes in the bottom leg are 1-5/16 in. on the center.

• Constructed of diecast and steel material
• Comes in a neutral gray color to blend with existing hardware, in a corrosion resistant, baked-on enamel finish
• Designed for use with awning windows manufactured by Pan American and Stanley Windows
• Features an L-shaped mounting hole pattern to provide greater stability when cranking
• Please refer to the line art drawing for dimensions and compare with your needs before ordering (Not universal)

This operator cover is constructed from diecast zinc. It comes finished in a white finish and features contemporary styling. This type of operator cover is designed to snap onto the worm housing of the truth entrygard operator.

• Worm drive and gears have a corrosive resistant e-guard coating
• Non-handed design
• Resists rust and corrosion
• Set screw holds handle in place
• Non-handed mounting

This is an awning operator of aluminum diecast construction with a natural aluminum finish used on Crown windows. It is right handed with a matching crank handle with a 2-5/8 inch offset link arm. It has a straight 2-1/4 inch link arm with with one hole that has a 3/8 inch diamter maounting hole. The mounting holes are 5-1/16 inch from center of the top hole to the center of the bottom hole and the two horizontal holes in the bottom leg are 1-7/16 inch on center.

• Designed for use with awning windows manufactured by Crown windows
• Features a straight link with a 3/8 inch mounting hole pattern to provide greater stability when cranking
• Diecast aluminum housing and crank with case hardened steel gears
• The mounting holes are 5-1/16 inch on center
• Mounting hardware is not included and ill need to be purchased separately

This is an awning operator of aluminum diecast construction with a gray baked enamel finish used on Tucker Windows. It is right-handed with a matching crank handle with a 2-3/8 inch link arm (as viewed for the inside looking out). It has an L shaped mounting hole pattern with a top hole that is off centered. The dimensions are 5-1/4 inch from center of the top hole to the center of the bottom hole and the 2 horizontal holes in the bottom leg are 1-1/4 inch on center.

• Constructed of diecast and steel material and is a right hand based on the handle location and mount to the Awning Operator Housing
• Comes in a neutral gray color to blend with existing hardware, in a corrosion resistant, baked-on enamel finish
• Designed for use with awning windows manufactured by Look-Rusco Windows
• Features an L-shaped mounting hole pattern to provide greater stability when cranking
• Please refer to the line art drawing for dimensions and compare with your original item before purchasing (Not Universal)

This Prime-Line H 3686 is an awning crank handle is bronze diecast and has a 11/32 inch bore spindle. This fits most awning operators with a 11/32 inch bore spindle such as the universal Prime-Line parts H 3554 or H 3555. It offers excellent torque for easy opening and closing of windows. The crank handle projects out from the operator 3-1/2 inch.

• Used by a variety of window manufacturers that have a 11/32 inch spindle
• Designed to only fit 11/32 inch spindle and anchors with the included set screw
• 3-1/2 inch projection from the operator
• Handle is diecast aluminum design in a bronze finish in a factory sealed package
• Please refer to the line art drawing for dimensions and compare to your needs before purchasing (Not Universal)

With the unique Prime-Line Window Operator Folding Crank Handle, you never have to worry about your shades and blinds being obstructed by the handle and not sitting flush with the window sill. Constructed of diecast zinc and extremely low-profile, the casement and awning cranks are designed to fit 11/32 inch Truth brand operator spindles and have a 2-9/64 inch reach with a 3-3/32 inch projection. It features a set screw at the base of the handle allowing it to lock onto the spindle, and a swivel knob at the tip for ease of operation, requiring far less torque than traditional low-profile handles. The unique design of the non-handed casement and awning window crank allows it to fold down when not in use. Shades, blinds, shutters and more can go straight down to the window sill without getting caught on the handle. Ideal for plantation shutters, retractable blinds and mini-blinds, the handle easily pulls out from its folded position to open or close the window. The white-enamel finish is baked on, creating a rust and corrosion resistant crank that is engineered to last. Installation is quick and easy, and all mounting hardware is included.

• EASY TO INSTALL – The non-handed window operator folding crank is extremely easy to install and all mounting hardware is included.